Figure skate blades start out in three separate parts. TOE plate. HEEL plate and the part that actually does the work on the ice. These are punched out on large presses. The blades are blanked out of long strips of steel which vary in Carbon content depending on the quality of the particular skate blade that is being made.(i.e. a Majestic would have a lower grade of steel than say a Phantom or Pattern 99 Although the steel used for all blades hardens to the same standard, the better grade would keep its edge longer(under equal conditions).
Before the three parts are put together to make the skate the blade section is hardened. This is done in large quantities hung on a frame and lowered into a high temperature salt bath for a set period of time to be evenly heated and while still glowing red are quenched in an oil bath. The shock of the sudden decrease in temperature causes the steel to harden . However, the hardness at this stage is too brittle, so the blades (still on the frame) are put into another salt bath of a lower temperature to temper to about what is called 60 degrees on the Rockwell scale. When cooled they are removed from the frames fed into a machine that grinds them to a set thickness.
The toe and heel plates (already ground) are then brazed to the blade. There are two methods of joining the parts together. John Wilson products are all silver soldered. This is a fairly low temperature braze achieved by electrical coil induction which causes the heat from the brazing to travel down onto the blade reducing the hardness to about 40 degrees Rockwell 'C' for about halfway but leaving the lower "working" half (about 5/16'') still at 60 degrees. Mitchell & King on the other hand silver solder theirs but the top quality blades such as Phantom, Gold Star etc. are hand brazed with bronze. This operation creates a lot more heat therefore the blades, by no means soft could be a bit patchy in their hardness. They are then set into an induction coil, electrically heated, rehardened and tempered about halfway up the blade.
You can tell if your blades are hand brazed. If you look at them you will notice that where the toe and heel plate joins the blade there is a very large radius. This method is very strong. Silver soldered skates will have a small bead of braze so the radius will be much smaller. However silver solder flows well and fills gaps readily. So, whichever method is used there will still be 5/16'' or more of correct hardness.
The assembled blade is now chrome plated, the profile is ground on and the chrome is removed from the edges by grinding. This is the line that you see each side of the blade edge. This is removed so that hardened steel and not chrome is at the working surface. There is of course extensive polishing and inspection before shipping.
Some people believe that they have to buy blades that are super expensive in order for them to become great skaters. You should buy well-built and *appropriate* equipment. Skaters gradually upgrade their equipment as their needs change, for example a skater may need to upgrade skates when they move from basic skating to their first jumps or from double to triple jumps. Advanced blades require the skater to perfect his/her technique.
Top of the line blades are designed for very advanced skaters. Advanced free-style blades have a longer radius and have *large* toe picks. Also, the portion of the blade that is used for spinning is much shorter than on intermediate blades; that means that unless you are perfectly balanced and positioned going into and during the spin you will start rocking on the blade. Intermediate blades like the MK Professional, Coronation Ace, etc. provide you more "room" to make corrections and continue spinning even if you are slightly off balance.
Just because the MK Gold Stars are typically over $400 does not mean that they are inherently better blades than MK Pros or Phantoms. Starting with MK Pro and Coronation Ace lines, the blades are all made using much the same materials and manufacturing process as described above. To put it succinctly, certain blades are more expensive simply because of supply and demand and a few slight design modifications like side honing which makes them marginally more costly to produce.
2. Put the skate upright on a table, and check the position of the bottom toepick. The blade should also be touching the table within one or two inches of the toe pick. If the blade touches the table further back, it means that the toe-pick is too low (probably a consequence of successive sharpenings). If the blades touches closer than 1 inch, the master toe-pick may have been ground off. In this case, the blades will be useless for learning spins and jumps.
3. Ask the skate sharpener at your rink to examine the blade. They can tell you if the blade is bent, incorrectly mounted or obviously damaged by abuse or bad sharpening.
If the only problem is that the toe pick is too low, ask your shop to grind it some to raise it. Never have the bottom (master) tooth ground off your blades unless you only intend to use them for figures. Otherwise the tooth fairy will never forgive you!!
Briefly, this is how your skate shop will mount the blades:
1)find the center of the tip of the sole and the center of the heel
and draw a line joining them.
2) place the front of the sole plate of the skate blade in line of
the front of the sole of the boot, and maintain the skate blade
along the line drawn. This will place the blade between the big toe
and first toe.
3) Screws may be placed only in the slotted holes, so that you can
try them and make minor adjustments (a blade position slightly
closer to the big toe is sometimes favored). Don't do any jumps
until the best position of the blades has been found and more
screws have been inserted.
1. The blade may have shifted sideways slightly when the front
or back pair of screws were tightened on the temp mounts, warping
the blade from front to back.
2. The holes for the permanent mounts might not be positioned
perfectly, warping the blade as in #1 above.
3. The heel might not be perfectly level or flat with respect to
the front of the boot. Old screw-holes may have created bumps on
the heel. Or the boot might have been manufactured with an uneven
heel. Such a heel will twist the blade.
If you have trouble getting good edges, first have the blades checked to make sure they are straight, properly sharpened and mounted perpendicular to the sole. If the problem persists, have someone watch to see if your blades "make snow" as you try to skate on the edge in question. If they do, this may point to a mounting problem which can be corrected by a slight shift of the blade mounting. You will need to tell the person remounting your blades which edges you are having trouble with.
You can also check if your blades are mounted correctly by yourself (you need recently sharpened blades for this test to ensure that the edges are even):
The smaller the radius, the more rocker (amount of back and forth rocking motion you can get when standing on the blade) it has. With small radius blades, you can do turns with less chance of falling as there is less blade on the ice. For the beginner, a 6' radius is fine as, among other things, it is very forgiving in the toe pick department -- you really need to lean way forward on them to catch the picks.
The bigger the radius, the flatter the blade. This will generate more speed as more of the blade contacts the ice. You will want a flatter blade (7 foot or more) as you become more advanced. When you start learning jumps, you will find that you need good edge control. Because you have more blade on the ice, you can start to prepare your body position for takeoff without falling off the edge so easily.
Finally, the width of the blade is yet another factor to consider: A deep hollow with a 3/8'' or smaller radius will be UNFORGIVING on freestyle blades, unless you are a child or have a very petite frame. This type of grind may yields crisp and fast 3-turns, ability to hold a very deep edge when landing jumps, and allows for fast spins IF you have them centered. An uncentered spin on deep edges will cause you to travel. See about traveling. On the other hand, such a small radius will be ideal for dance or hockey blades: Because these blades are narrower than freestyle blades, the need a deeper grind to get the same grip on the ice.
A shallow "figure" hollow with a 1'' or larger radius will require a more correct lean to prevent skidding and requires more frequent sharpening, but yields an easy glide and clean tracings.
Most skating blades have the same constant width along its full length. However, some advanced freestyle figure skating blades have a concave section ("side honing"). Side honed blades are thicker at the stanchions and the edge stripe and thinner in between. You can tell side honed blades because reflections appear inverted.
Another modification to the edge profile found in advanced blades is "tapering". Tapered blades are thicker at the front near the toepicks and thinner at the tail, i.e. the edges are not parallel. Parabolic blades are thinner in the middle section and thicker at both ends. Some models or custom made blades can be both side-honed and tapered.
These modifications make the blade lighter (because of the removed steel) and supposedly provide a better grip on the ice. Not surprisingly, the more laborious manufacturing process translates in a higher price. Whether they actually provide any real advantage is a matter of discussion.
Take your skates to a pro shop or ask some regular skaters at your rink where they get theirs sharpened. Skate sharpening is NOT a do-it-yourself project! Skates are expensive and it only takes one bad sharpening to turn them into scrap metal!
1) You have to know and trust your sharpener,Skates properly sharpened will have a smooth concave grind accurately centered along the length of the blades, edges squared (parallel to the bottom of the boot) and level with each other (inside edge at same height as outside edge) for the length of the blade. Proper sharpening will maintain the correct rocker for the life of the blade.
Freestyle sharpenings will have typically a 1/2'' radius concave grind and will be in a sharp condition. The edges of a deep freestyle grind have the great advantage of holding jump landings on hard or soft ice and also will outlast a shallow grind by a considerable amount of time. They will also hold landings on missed jumps and give the skater that extra split second to catch their balance and avoid unnecessary falls. A sharp deep grind takes a little effort on the part of the skater to adapt but is well worth the effort and once adapted to it will be no problem in future sharpenings.
Figure sharpenings will have 1 1/4'' radius concave grind and will be in a medium sharp condition. The figure grinds are extremely smooth and flow freely on the ice. More shallow (greater radius) grinds have extreme flow on the ice but are usually suitable only for the more advanced skater.
Combination sharpenings will have 3/4'' radius concave grind and will be in a medium sharp condition so that the skater can skate figures with ease or they can be used for general skating. The grind will be of smooth finish and will flow quite freely on the figures (although not as freely as a true figure grind). This grind can be used for all jumps and spins and will hold well while blades are in a sharp condition. This grind is also very suitable for occasional skaters and some dancers; and is also good for adults to start with.
Skates should be resharpened before they become so dull that you begin to slip on hard ice (eg: not flooded since last night). This will also minimize the adjustment you need to make to your newly sharpened skates. Nicks in the blades should also be attended to. Bad nicks in the edges will ruin the finest sharpenings.
When the blade is ground down a long way after many sharpenings, the relationship between the bottom pick and the blade edge should be maintained by removal of steel from the pick. There should be about 1/2'' lift at the heel before the pick makes contact with the ice. Just because your blades are ground down past the line of chrome plating, that is not an indication that you need new ones. There is still lots of life left as long as the sharpener replaces that "line" and adjusts the pick height.
Beware of how some shops do their sharpening: Some shops flat-grind the blade first, and then hollow grind. This wears the blade at an accelerated rate.
There are two kinds of blade covers, hard rubber/plastic guards and terry-cloth "soakers". The plastic guards should be worn *any time* you step off the ice. Even "safe" rubber mats or carpets accumulate dirt and grit from the shoes of pedestrians, and this grit will nick and round off the fine edges of your blades much faster than gliding across the ice. Do not leave them on your skates between sessions as they will trap water and cause your blades to rust.
The cloth soakers are put on after you have removed your skates and wiped them dry with a rag. They protect your blades from bumping in transit and wick away any condensation so your blades won't rust. If you still have problems with rust or want to store your skates, rub a drop of oil or Vaseline along the bottoms of the blades.